View previous topic :: View next topic |
Author |
Message |
elnevio Gate Opener
Joined: 20 Sep 2013 Odometer: 5 Location: Gloucester
|
Posted: Tue Oct 08, 2013 8:52 pm Post subject: Unsuccessful!
|
|
|
With thanks to jic44 again, I have now followed the procedure, but it looks like I might be the first one to not achieve success!!
The background is as follows. About six weeks ago, while we were visiting friends away from home, we experienced the flashy glow plug light and no starting, there was no joy for about an hour or so, but once the recovery chap arrived, the light had mysteriously stopped flashing and the car now started! It has recently had new glow plugs anyway (last year), and the recovery bloke suggested cleaning up the cable contact (is this the ground?) on the glow plug rail.
Then, it ran perfectly fine and normal until a couple of weeks ago, when it reappeared. The difference this time was that no amount of waiting or anything made the light go away! I cleaned up the ground contact as mentioned, just in case.
Anyway, I found this thread, checked the details, and determined that this must be the same problem with our 2000 GV. We had the error code 83, Mazda RF series 2.0TD engine, correct ECU and the correct immo unit.
So I followed the solution instructions, and double-checked that the required details matched, which they did.
Then when turning the key, I noticed that the glow plug light no longer flashed, but it did stay on (before attempting to start).
I can't get any codes (glow plug light just stays on).
Upon attempting to start, it eventually caught, but whitish smoke was also appearing from the rear of the engine bay somewhere! Further investigation revealed nothing.
As the battery was somewhat weak, I took it out, and left it charging all day. Upon trying again, I stuck with it, i.e. left the ignition on when it fired - but it will not run, even with the application of throttle as soon as it fires. The whitish smoke is still appearing (not quite as thick as the first occasion) from behind the engine when 'nearly' starting, drifting wispily up through the intercooler. It did smell a little 'fuelly', but I can't see anything obvious.
It happened fairly quickly, so I was thinking it was electrical. It could have been coming from the area of the starter motor, but all the cables appear firmly attached, without any obvious signed of scorching or melting. Even if it there was a problem with the starter motor unit or wiring, I would still expect the engine to run once it fired, as the starter motor was still turning the engine over, i.e. doing its job.
We are not aware of any similar problems previously, and the car has been sterling up until this. Admittedly, we've only had it for two and a half months, but my mum and dad had it for nearly two years.
Any ideas what this problem could be? I have little experience with diesels, so please feel free to suggest the obvious! Sorry for the length of the post, but I know how difficult it is to diagnose problems from afar, and I would like to give as much info as I can.
I'd love to get this sorted, as while I have a van for work, the wife is using my car for work and school, and that only averages around 16 mpg! Eek!
|
|
Back to top |
|
|
|
Scooby2Scudo Gate Opener
Joined: 14 May 2012 Odometer: 8 Location: Ireland
|
Posted: Wed Oct 09, 2013 10:00 am Post subject:
|
|
|
It may be worth back tracing the work the recovery mechanic done, did he chop or change any of the glow plug wiring? Can you hear the glow plug relay click as you let the engine heat?
|
|
Back to top |
|
|
elnevio Gate Opener
Joined: 20 Sep 2013 Odometer: 5 Location: Gloucester
|
Posted: Wed Oct 09, 2013 10:52 am Post subject:
|
|
|
Scooby2Scudo wrote: | It may be worth back tracing the work the recovery mechanic done, did he chop or change any of the glow plug wiring? Can you hear the glow plug relay click as you let the engine heat? |
Thanks for the response.
The recovery bloke didn't do anything, as by the time he got there, it started no problem!
Anything is still worth trying though. Where is the glow plug relay located for me to try and check/listen to?
|
|
Back to top |
|
|
Scooby2Scudo Gate Opener
Joined: 14 May 2012 Odometer: 8 Location: Ireland
|
Posted: Thu Oct 10, 2013 1:20 pm Post subject:
|
|
|
Relay location I am not possitive on but I'd check the relays under the bonnet, you may need help from someone. I can hear mine from inside, you should hear it once the windows open, bonnets open I 'd say
|
|
Back to top |
|
|
Toseland Mud Obsessed
Joined: 25 Oct 2011 Odometer: 3209 Location: cardiff
1999 Suzuki Vitara
|
Posted: Thu Oct 10, 2013 6:54 pm Post subject:
|
|
|
does sound like a sticking relay..
but also do check that the immo is letting fuel into the pump, i would suggest that if it fires breifly its getting some..
1. check the system is primed properly
2. check you have voltage across ALL of the glow plugs, and that they are heating up (you can do this either with a meter, or by removing the glowplug and having someone turn the ignition on, the end should glow white hot so be careful
3. painful i know, but see if you can get some diagnostics to indicate whether the ECU is actually turning on the fuel, it may well be that the fuel stop solonoid isnt working properly, is sticky, etc etc.
__________________________________ I live by 2 sayings:
1. The beatings will continue until morale improves
2. Pain is just Weakness leaving the body..
The feeling you get when you first smash your shaft out, is one you will never forget.. especially if you do it in front of 10 guys. |
|
Back to top |
|
|
elnevio Gate Opener
Joined: 20 Sep 2013 Odometer: 5 Location: Gloucester
|
Posted: Sat Oct 12, 2013 12:27 pm Post subject:
|
|
|
Really good stuff, thanks. I'll get on this later next week when I'm home again and have got the chance!
|
|
Back to top |
|
|
dcorry1 Gate Opener
Joined: 17 Oct 2013 Odometer: 1
|
Posted: Sat Oct 19, 2013 10:45 am Post subject: Immobilizer problem
|
|
|
Could some please pm me the method to bypass the immobilizer. my work college's 00 grand vitara is currently not running and has the same problem. thanks.
|
|
Back to top |
|
|
elnevio Gate Opener
Joined: 20 Sep 2013 Odometer: 5 Location: Gloucester
|
Posted: Mon Oct 28, 2013 11:05 am Post subject:
|
|
|
Just about to see if I can fiddle around with some of the suggestions. I think it's stopped raining!
In the meantime, I am considering alternative possibilities and would like confirmation on one point:
Assuming it is an ECU problem (it might be - I may have broken something in the process; anyway...), I believe that if I source a replacement ECU, I could then tow the vehicle to Suzuki, and have them recode the ECU to match the existing immobiliser unit and keys.
Is this correct? Or would I also need to obtain a matching set of immobiliser unit, keys and barrels? I don't fancy that much.
|
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Fri Nov 15, 2013 4:05 pm Post subject:
|
|
|
well the gv wouldnt start after school run .. glow plug light flashing .. after several turns and about 20 mins looking like a fool it started .. can someone send me the mod to sort .. many thanks
|
|
Back to top |
|
|
rhinoman Mud Obsessed
Joined: 04 Sep 2004 Odometer: 3277 Location: Brinkworth, Wilts
|
Posted: Fri Nov 15, 2013 4:52 pm Post subject:
|
|
|
Its usually the immo that's faulty rather than the ECU. A Suzuki dealer should be able to code the key and ECU to a replacement immo.
__________________________________ 2000 Vitara 4u2, 3+3 lift, 33s, winch, safari rack, steel front axle and 5:83 R&Ps, LWB brakes
1986 SJ413K Pickup, 1.6 conversion
2006 Jimny JLX+, stock |
|
Back to top |
|
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Tue Nov 19, 2013 11:08 am Post subject:
|
|
|
can i just disconnect the immo ... but still have the key fob to unlock the doors ..or do the central locking and immo .. work together ?
|
|
Back to top |
|
|
rhinoman Mud Obsessed
Joined: 04 Sep 2004 Odometer: 3277 Location: Brinkworth, Wilts
|
Posted: Tue Nov 19, 2013 7:29 pm Post subject:
|
|
|
The central locking and immo are separate items if you disconnect the immo the engine won't start.
__________________________________ 2000 Vitara 4u2, 3+3 lift, 33s, winch, safari rack, steel front axle and 5:83 R&Ps, LWB brakes
1986 SJ413K Pickup, 1.6 conversion
2006 Jimny JLX+, stock |
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Tue Nov 19, 2013 10:26 pm Post subject:
|
|
|
surely the toad can be removed . i am thinking that is where the problem is . thanks for your input . ta
|
|
Back to top |
|
|
Toseland Mud Obsessed
Joined: 25 Oct 2011 Odometer: 3209 Location: cardiff
1999 Suzuki Vitara
|
Posted: Tue Nov 19, 2013 10:40 pm Post subject:
|
|
|
you have a message on SWS mate
__________________________________ I live by 2 sayings:
1. The beatings will continue until morale improves
2. Pain is just Weakness leaving the body..
The feeling you get when you first smash your shaft out, is one you will never forget.. especially if you do it in front of 10 guys. |
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Wed Nov 20, 2013 6:43 am Post subject:
|
|
|
hey toseland .. no pm .. sws ? can you save the day pal .. i just want rid of the toad .. the truck is 13 years old now .. cant see anyone wanting to pinch it now ..
|
|
Back to top |
|
|
elnevio Gate Opener
Joined: 20 Sep 2013 Odometer: 5 Location: Gloucester
|
Posted: Sat Nov 23, 2013 2:58 pm Post subject:
|
|
|
I've had no problem with the TOAD. It seems to be operating correctly. I have had the same alarm (Ai606) on two different vehicles. As far as I know, it usually cuts the ignition and the fuel pump. The stock immo (which this thread deals with) is retained, but it, I believe, just affects the fuel pump.
Anyway, I have managed to get mine to run!
But only by keeping the key in 'START'. After the starter motor disengages, it then winds up to high speed. Obviously, I do not want to do this for long. But the engine runs and revs. As soon as I return the key to position 2, i.e. ignition, it stops as if I have turned the key to ACC or OFF.
So fuelling is not an issue. The smoke I got was definitely fuelly but when 'running' as above, there was no smoke at all.
I am thinking that the glow plug relay may still be the potential culprit now, but need to know where it is? I'll trawl the forums for it, and maybe ask it as a standalone question, but if anybody can tell me exactly, that would be appreciated!
|
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Tue Nov 26, 2013 8:52 pm Post subject:
|
|
|
toad removed .. all good ..
|
|
Back to top |
|
|
icerman Gate Opener
Joined: 29 Nov 2013 Odometer: 2 Location: Sweden
|
Posted: Sat Nov 30, 2013 9:51 pm Post subject:
|
|
|
Hello!
I have code 83 and I begging to know how I can passby the imobilizer om my GV.
Please send a pm if you know
Best Regard Daniel Lundström, Sweden
|
|
Back to top |
|
|
detrytus Gate Opener
Joined: 01 Dec 2013 Odometer: 1
|
Posted: Sun Dec 01, 2013 1:23 pm Post subject:
|
|
|
Hello All,
yesterday my GV 2.0 TD died on gas station. Glowplug flashing. Checking the flash codes gave 81 result - immobiliser. Looking for the solution I found this topic. Could anyone please PM me the bypass solution for immo problem? I would be really greatfull. I need the car runing as soon as possible. Thanks.
|
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Sun Dec 01, 2013 4:58 pm Post subject:
|
|
|
i took mine to garage and ripped toad out .. all good since .. he didnt by pass , just removed as stock when built ..
|
|
Back to top |
|
|
|
twanger Gate Opener
Joined: 02 Dec 2013 Odometer: 6 Location: county durham
|
Posted: Tue Dec 03, 2013 1:03 pm Post subject:
|
|
|
sandyjet62 wrote: | Hi all, and thanks for all your help,
Well the problem is sorted now. Not by me I hasten to add, but by the very clever man I bought the car from. (as I said, a coleague at work). I knew it was an immobaliser problem, was quoted £100 + plus by Suzuki to look at it and approx £500 if it turned out to be the ecu.
Anyway, it turns out that if you have the RF engine and the immobiliser system has Denso ECU it is possible to dissconnect the immobiliser. In fact it is very easy to disable the immobiliser at no cost at all.
unfortunatley, i dont think it should be put up to open forum for the security of other GV owners with the same system. But I will gladly give the info to a mod and let them decide. It may not be a big secret but I could not find this info on the net anywhere, I was about to give up and look at replacing the unit the man with the plan came up with the solution.
Thanks again all. | hi i need your help asap my vitara also failed to restart and the glow plug light is flashing
__________________________________ if theres no smoke theres no poke oops thats only for a 2 stroke |
|
Back to top |
|
|
twanger Gate Opener
Joined: 02 Dec 2013 Odometer: 6 Location: county durham
|
Posted: Tue Dec 03, 2013 1:03 pm Post subject:
|
|
|
sandyjet62 wrote: | Hi all, and thanks for all your help,
Well the problem is sorted now. Not by me I hasten to add, but by the very clever man I bought the car from. (as I said, a coleague at work). I knew it was an immobaliser problem, was quoted £100 + plus by Suzuki to look at it and approx £500 if it turned out to be the ecu.
Anyway, it turns out that if you have the RF engine and the immobiliser system has Denso ECU it is possible to dissconnect the immobiliser. In fact it is very easy to disable the immobiliser at no cost at all.
unfortunatley, i dont think it should be put up to open forum for the security of other GV owners with the same system. But I will gladly give the info to a mod and let them decide. It may not be a big secret but I could not find this info on the net anywhere, I was about to give up and look at replacing the unit the man with the plan came up with the solution.
Thanks again all. | hi i need your help asap my vitara also failed to restart and the glow plug light is flashing
__________________________________ if theres no smoke theres no poke oops thats only for a 2 stroke |
|
Back to top |
|
|
twanger Gate Opener
Joined: 02 Dec 2013 Odometer: 6 Location: county durham
|
Posted: Wed Dec 04, 2013 4:24 pm Post subject: the ecu
|
|
|
hi can somebody tell me where abouts the ecu is located on a 2.0 td vitara please
__________________________________ if theres no smoke theres no poke oops thats only for a 2 stroke |
|
Back to top |
|
|
icerman Gate Opener
Joined: 29 Nov 2013 Odometer: 2 Location: Sweden
|
Posted: Wed Dec 04, 2013 6:17 pm Post subject:
|
|
|
Doesn´t anyone know how i could remove the imo.
I can start the car simply by disconect the connection to the ABS controller. But i want to have ABS brakes when i drive
|
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Wed Dec 04, 2013 7:37 pm Post subject:
|
|
|
sorry cant help . ta
|
|
Back to top |
|
|
twanger Gate Opener
Joined: 02 Dec 2013 Odometer: 6 Location: county durham
|
Posted: Fri Dec 06, 2013 2:35 pm Post subject:
|
|
|
elnevio wrote: | I've had no problem with the TOAD. It seems to be operating correctly. I have had the same alarm (Ai606) on two different vehicles. As far as I know, it usually cuts the ignition and the fuel pump. The stock immo (which this thread deals with) is retained, but it, I believe, just affects the fuel pump.
Anyway, I have managed to get mine to run!
But only by keeping the key in 'START'. After the starter motor disengages, it then winds up to high speed. Obviously, I do not want to do this for long. But the engine runs and revs. As soon as I return the key to position 2, i.e. ignition, it stops as if I have turned the key to ACC or OFF.
So fuelling is not an issue. The smoke I got was definitely fuelly but when 'running' as above, there was no smoke at all.
I am thinking that the glow plug relay may still be the potential culprit now, but need to know where it is? I'll trawl the forums for it, and maybe ask it as a standalone question, but if anybody can tell me exactly, that would be appreciated! | i also have the same problem now iv removed the imobiliser can anybody help as this is my only means of transport
__________________________________ if theres no smoke theres no poke oops thats only for a 2 stroke |
|
Back to top |
|
|
twanger Gate Opener
Joined: 02 Dec 2013 Odometer: 6 Location: county durham
|
Posted: Fri Dec 06, 2013 2:35 pm Post subject:
|
|
|
elnevio wrote: | I've had no problem with the TOAD. It seems to be operating correctly. I have had the same alarm (Ai606) on two different vehicles. As far as I know, it usually cuts the ignition and the fuel pump. The stock immo (which this thread deals with) is retained, but it, I believe, just affects the fuel pump.
Anyway, I have managed to get mine to run!
But only by keeping the key in 'START'. After the starter motor disengages, it then winds up to high speed. Obviously, I do not want to do this for long. But the engine runs and revs. As soon as I return the key to position 2, i.e. ignition, it stops as if I have turned the key to ACC or OFF.
So fuelling is not an issue. The smoke I got was definitely fuelly but when 'running' as above, there was no smoke at all.
I am thinking that the glow plug relay may still be the potential culprit now, but need to know where it is? I'll trawl the forums for it, and maybe ask it as a standalone question, but if anybody can tell me exactly, that would be appreciated! | i also have the same problem now iv removed the imobiliser can anybody help as this is my only means of transport
__________________________________ if theres no smoke theres no poke oops thats only for a 2 stroke |
|
Back to top |
|
|
twanger Gate Opener
Joined: 02 Dec 2013 Odometer: 6 Location: county durham
|
Posted: Fri Dec 06, 2013 2:37 pm Post subject:
|
|
|
twanger wrote: | elnevio wrote: | I've had no problem with the TOAD. It seems to be operating correctly. I have had the same alarm (Ai606) on two different vehicles. As far as I know, it usually cuts the ignition and the fuel pump. The stock immo (which this thread deals with) is retained, but it, I believe, just affects the fuel pump.
Anyway, I have managed to get mine to run!
But only by keeping the key in 'START'. After the starter motor disengages, it then winds up to high speed. Obviously, I do not want to do this for long. But the engine runs and revs. As soon as I return the key to position 2, i.e. ignition, it stops as if I have turned the key to ACC or OFF.
So fuelling is not an issue. The smoke I got was definitely fuelly but when 'running' as above, there was no smoke at all.
I am thinking that the glow plug relay may still be the potential culprit now, but need to know where it is? I'll trawl the forums for it, and maybe ask it as a standalone question, but if anybody can tell me exactly, that would be appreciated! | like above i also have the same problem now iv removed the imobiliser can anybody help as this is my only means of transport | ps mine never has had a toad just the factory imobiliser
__________________________________ if theres no smoke theres no poke oops thats only for a 2 stroke |
|
Back to top |
|
|
baderdog Gate Opener
Joined: 30 Dec 2013 Odometer: 6 Location: Norfolk uk
|
Posted: Mon Dec 30, 2013 1:46 pm Post subject: GV immobilizer dead
|
|
|
Hi my first time on this forum, I have a 2000 Grand Vitara which on Xmas eve decided to immobilize itself having had a flat battery( due to the wife leaving the courtesy light on ) we now have the flashing heater plug light and no fuel pump activation, having checked everything out it is deffo the same old problem with the immobilizer, I understand that some members have managed to bypass this and would very much appreciate someone telling how its done, had the GV for 11years without a hint of problems so I guess its time something went wrong..
__________________________________ Jeep TJ wrangler 40ltr 3"lift lpg>>Jeep CJ7 1986 black laredo completely standard never welded Never goes out in the wet " Suzuki GV TD y2k great little workhorse |
|
Back to top |
|
|
matt77 Gate Opener
Joined: 11 Feb 2013 Odometer: 15 Location: hereford
|
Posted: Mon Dec 30, 2013 8:54 pm Post subject:
|
|
|
check battery ,, give it a charge and test ..
|
|
Back to top |
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot post calendar events in this forum
|
|
|